Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
We have noticed this article about Tools You Need to Install a New Bathtub down the page on the web and think it made good sense to talk about it with you on this page.
Mounting a bathtub isn't exactly rocket science, however it does need solid plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is likewise a reasonably difficult project. If the old bathtub is conveniently obtainable, the job can move easily; if you need to open up a wall to remove the old bathtub and also place the new bath tub, the job is much harder. In either case, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the work and also fit trying it. Rather than working with a contractor to take over a halfway-completed task, it is far better to think about using one before you start. Possibilities are you might need an expert plumber to make tube links.
This write-up will certainly aid you install a new bathtub in your shower room if you have already gotten a brand-new bathtub and also do not require to change the setup of your previous supply of water pipelines.
Your devices and product checklist should comprise the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath must be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of the two taps using 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be quite troublesome because of the limited gain access to that is frequently the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the staying water that will certainly come from the pipelines. As soon as the supply pipes have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary faucets from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using the two wooden boards under its feet, put the tub in the required setting. The wood boards are practical in equally spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the spirit level and also changing the feet on the tub up until the spirit level reviews level.
To set up faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the various other faucet.
Turn on the supply of water as well as examine all joints as well as new pipework for leaks as well as tighten them if needed. Load the tub and also check the overflow electrical outlet as well as the normal outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling and also sealing around the bath tub should wait till the tub has been made use of at least when as this will certainly settle it right into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in place between the faucet as well as the sink. Protect the tap in place with the maker supplied backnut. As soon as the tap is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous type needs to be linked to the tap ends first, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to break a rigid seal, causing the water to penetrate the wall in between the bath and also the tiling, resulting in issues with moisture and feasible leakages to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as fittings. They are sold in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in use. The sealer can break rather very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the marketplace. It is advisable to fit the tiles making use of waterproof or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I hope you enjoyed our topic about How to Install a Bathtub. Thanks a ton for spending some time to browse our blog post. Those who enjoyed our blog posting plz be sure to share it. Thank-you for your time invested reading it.
Overflow? We're here! Report this page